Pinball Nirvana Home Page

Go Back   Pinball Nirvana Forums > Real Pinball > Maintenance & Repair

Maintenance & Repair Discuss and offer tips on real life machines.

Reply
 
Thread Tools Search this Thread
  #1  
Old 07-03-2017, 07:57 PM
new_pinhead's Avatar
new_pinhead new_pinhead is offline
Inserted Coin
 

Join Date: Feb 2012
Posts: 39
Credits: 14,642.43
Thanks: 5
Thanked 5 Times in 5 Posts
Rep Power: 0
new_pinhead is on a distinguished road
Unhappy very weak flipper on pop-a-card

left flipper very weak on my Gottlieb Pop-A-Card. Already replaced coil but made no difference at all. will barely send ball to middle of playfield or worse. any help would be greatly appreciated.
Reply With Quote
  #2  
Old 07-04-2017, 05:46 PM
new_pinhead's Avatar
new_pinhead new_pinhead is offline
Inserted Coin
 

Join Date: Feb 2012
Posts: 39
Credits: 14,642.43
Thanks: 5
Thanked 5 Times in 5 Posts
Rep Power: 0
new_pinhead is on a distinguished road
Default

looking thru other posts I found reference to pinwiki for lots of good info on em pin repair. just quickly browsing topics I found many things to check for weak flipper. al;so see a WHOLE lot of other very useful and detailed info on other repairs commonly needed. Thanks.
Reply With Quote
  #3  
Old 07-04-2017, 05:49 PM
new_pinhead's Avatar
new_pinhead new_pinhead is offline
Inserted Coin
 

Join Date: Feb 2012
Posts: 39
Credits: 14,642.43
Thanks: 5
Thanked 5 Times in 5 Posts
Rep Power: 0
new_pinhead is on a distinguished road
Default

found reference in post by lockuplever about his Grand Prix problems. thanks pinballdaveh.
Reply With Quote
  #4  
Old 07-06-2017, 07:21 AM
pinballdaveh's Avatar
pinballdaveh pinballdaveh is offline
Pinball Technician
 

Join Date: Aug 2012
Location: poconos
Posts: 863
Credits: 53,629.92
Thanks: 205
Thanked 303 Times in 259 Posts
Rep Power: 17
pinballdaveh is a jewel in the roughpinballdaveh is a jewel in the roughpinballdaveh is a jewel in the roughpinballdaveh is a jewel in the rough
Default

Other than file cleaning the flipper button switches and end of stroke switches, the fiber flipper link needs to be checked or changed. To check hold the flipper coil plunger with one hand and the flipper bat with the other hand, and wiggle the flipper bat. the more play there is the less strength the flipper will have. Punching out the roll pins will allow you to change the link. Pinball resource should still sell these.
Reply With Quote
The Following User Says Thank You to pinballdaveh For This Useful Post:
new_pinhead (07-06-2017)
  #5  
Old 07-06-2017, 09:40 AM
new_pinhead's Avatar
new_pinhead new_pinhead is offline
Inserted Coin
 

Join Date: Feb 2012
Posts: 39
Credits: 14,642.43
Thanks: 5
Thanked 5 Times in 5 Posts
Rep Power: 0
new_pinhead is on a distinguished road
Default

Thanks pinballdaveh. I'll look at those . Don't recall seeing any of those specific tips on pinwiki regarding weak flippers. Thanks again.
Reply With Quote
  #6  
Old 07-07-2017, 01:01 AM
Coil_Smoke's Avatar
Coil_Smoke Coil_Smoke is offline
Pinball Pusher
 

Join Date: Dec 2011
Location: Planet Dirt
Posts: 1,004
Credits: 105,478.30
Thanks: 501
Thanked 371 Times in 294 Posts
Rep Power: 19
Coil_Smoke is just really niceCoil_Smoke is just really niceCoil_Smoke is just really niceCoil_Smoke is just really nice
Wink The End, Of Stroke Woes...?

It is important for the End Of Stroke Switch not open to soon. Those contacts carry the bulk of the current flowing thru the main flipper coil. It they open too soon the coil will act real weak. After cleaning they should be adjusted to open only as far as necessary. As soon as they open the power must flow thru the holding coil winding too, as in>>>real weak flipper. Those contacts are supposed to self clean(sort of anyway) as they wipe past each other while operating. Like other pinball contacts they can benefit from being used. I have had flipper action improve during use shortly after cleaning those EOS contacts.
P.S. You can find troubles with EOS contacts by by-passing them with a clip lead. If your flipper acts right with the contacts shorted..."There's Your Problem Right There"
__________________

When Lit

Last edited by Coil_Smoke; 07-07-2017 at 10:16 AM.
Reply With Quote
The Following User Says Thank You to Coil_Smoke For This Useful Post:
new_pinhead (07-08-2017)
  #7  
Old 07-28-2017, 02:02 PM
mamemad mamemad is offline
Inserted Coin
 

Join Date: Mar 2016
Posts: 6
Credits: 290.53
Thanks: 0
Thanked 2 Times in 2 Posts
Rep Power: 0
mamemad is on a distinguished road
Default weak flipper

they are right rember eos switch opens so the hold winding is left if nc eos switch needs good pressure and need to be clean and should open at near end of stroke check wiring of flipper it may be wrong check backstop as well hope this helps
Reply With Quote
  #8  
Old 08-06-2017, 10:47 PM
ddaniel25 ddaniel25 is offline
Inserted Coin
 

Join Date: Aug 2017
Posts: 1
Credits: 205.13
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
ddaniel25 is on a distinguished road
Default flippers slowly stopped working

flippers slowly stopped working on our bugs bunny birthday pinball can anyone help
Reply With Quote
  #9  
Old 08-07-2017, 01:40 AM
mamemad mamemad is offline
Inserted Coin
 

Join Date: Mar 2016
Posts: 6
Credits: 290.53
Thanks: 0
Thanked 2 Times in 2 Posts
Rep Power: 0
mamemad is on a distinguished road
Default b bunny flippers

check eos if there not sure on b bunny weak flippers on ss pinballs can be a worn backstop check fuses for flippers cabinet switches but slowly stopped working i look at mechanical components bush backstop etc if you need order a flipper rebuild kit from one of the online vendors good luck
Reply With Quote
  #10  
Old 08-07-2017, 04:06 AM
Coil_Smoke's Avatar
Coil_Smoke Coil_Smoke is offline
Pinball Pusher
 

Join Date: Dec 2011
Location: Planet Dirt
Posts: 1,004
Credits: 105,478.30
Thanks: 501
Thanked 371 Times in 294 Posts
Rep Power: 19
Coil_Smoke is just really niceCoil_Smoke is just really niceCoil_Smoke is just really niceCoil_Smoke is just really nice
Default

I see you mentioned other intermittent issues in chat.Try re-seating your connectors and socketed IC's
__________________

When Lit
Reply With Quote
Reply

Bookmarks

Tags
flipper, gottlieb em

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 01:04 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Template-Modifications by TMS
Credits System provided by vBCredits II Deluxe (Lite) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.15 (Lite) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.